Pneumatic fast connection male thread 1/8 to tube 12mm INOX

Description

Pneumatic fast connection male thread 1/8 to tube 12mm INOX

When selecting the connection, check the connection thread and the outer diameter of the pipe. Pneumatic fast connection male thread 1/8 to tube 12mm INOX connects male thread of nominal size 1/8 inch to tube outside diameter 12 mm. The price is EUR 3 with VAT. Check the thread standard and the working conditions of the concrete execution before ordering.

A tube with an external diameter of 12 mm does not mean that the whole connection has such a flow-through! In the selection we first check both ends of the connection: screw connection of the device and pneumatic hose. A straight INOX connection combines a male thread of the nominal size of 1/8 inches and a tube connection with an external diameter of 12 mm. The price is EUR 3 with VAT. A small component in which the correct selected size decides the usefulness of the entire joint.

When choosing, we check the dimensions and conditions of use. This version is the candidate for connecting the threaded position 1/8 to the tube 12 mm without additional adapter, but only after the threading standard and technical suitability has been confirmed.

INOX mount: confirmed properties

For this product we provide the following validated information:

• Title: Pneumatic fast connection male thread 1/8 to tube 12mm INOX.
• Type: goods, pneumatic fast connection level.
• Material: stainless steel INOX.
• Thread: male, nominal size 1/8 inches.
• Pipe connection: for a pneumatic tube with an external diameter of 12 mm.
• Price: EUR 3 with VAT.

The flat design allows connection in the same axle when the arrangement of the device so permits. The advantage of this combination is connecting those two sizes in one connection. INOX does not refer to the steel class, the composition of all seals or the suitability for each chemical.

Thread 1/8 and tube 12 mm: correct choice

The thread marking in thumbs is not an external thread diameter indication in millimetres. Codes 1/8 should therefore not be converted into millimetres and the result should not be used as a measure to identify the thread. The exact thread type G, R or NPT of this product is not confirmed. Before purchasing, we check the standard, the actual dimensions and the method of sealing both parts.

A different rule applies to the pipe: 12 mm means its outer diameterThe tube with an internal diameter of 12 mm is therefore not yet suitable. We also check the material, tolerance and compatibility of the hose with the installation. Just a similar look is not enough.

Flow through connection 1/8 to 12 mm

A larger pipe does not remove the narrow part of the connection. For a combination of 1/8 and 12 mm, the required flow rate, the internal geometry of the coupling and the allowed pressure drop should be checked separately. Internal dimensions of this product are not confirmed; the flow is not estimated from the outer diameter of the tube.

Collect data on the consumption and operating cycle of the device. Let us check that the entire route between the source and the consumer meets its needs. The connection itself does not provide the system's capability.

Comparison: direct connection or additional adapter

As a comparative solution we take a separate thread adapter and a separate connector for the tube 12 mm connected consecutively. We assess the composition of the connection and the necessary work.

Where the direct connection is appropriate, the release of the adapter may facilitate the assembly and inspection of the coupling. That's a practical advantage. However, if you need a different standard or a specially documented implementation, an appropriate adapter may be necessary. The savings are only estimated with comparable requirements.

Installation and inspection of pneumatic hoses

Before the operation, we safely stop, relieve and prevent unexpected start-up. For the final assembly we use the manufacturer's instructions of the concrete connection. Without them, we do not determine the moment of screwing, the depth of insertion or the type of seal.

1. Let's check the threads of the device, the pipe data and the available space for a flat connection.
2. Check the thread and end of the pipe; do not use damaged or oval parts without judgment and proper preparation.
3. The hose is prepared according to the instructions of its manufacturer and the cuttings are prevented from entering into the connection.
4. Seal and screw the thread exclusively in the manner provided for the certified thread performance.
5. After assembly, perform a controlled functional test and closeness check according to the device procedure.

Support the hose in such a way that the coupling is not loaded by pulling or inappropriate bending. We also leave access for inspection and disconnect. Quick connection has the most practical value when it can be properly assembled and later reviewed!

HACCP: cleaning and accessibility in the diet

In planning production according to HACCP principles, we address risks, how to clean and document controls. HACCP is not a property that would be acquired by an INOX connection. European Commission in Review food hygiene provides a common framework of hygiene rules for food business.

First, determine where the coupling will be installed and whether it is a direct contact with food, the possibility of indirect pollution or a separate pneumatic drive. Then we check availability for cleaning, places of retention of dirt, and the possibility of inspection and replacement. The compatibility of cleaners, their concentrations, operating time and temperature is checked for all exposed materials. We do not guarantee the use of any cleaning products.

Food contact: supporting documents for the whole set

For direct contact with food we require evidence for a concrete complete assembly, including connection, all seals and hose. Stainless steel is not sufficient evidence in itself. European Commission food contact materials clarifies the importance of the safety of materials and their production.

Documentation is linked to the intended food, contact conditions and cleaning process. Before installation we require identification of the supplied parts and the available evidence of their suitability. If they cannot be confirmed for the required use, this connection is not recommended for such use. Compliance with these requirements is currently not ensured.

GMP in pharmacy: documentation and traceability

GMP means the requirements of good manufacturing practice which also affect the design, maintenance and documentation of production. They are considered for medicinal products EudraLex Volume 4Mount not automatically HACCP, GMP or USP certified. Its use does not confirm the conformity of the production line.

For pharmaceutical use we check the location of the installation, accessibility, method of cleaning and required traceability. The records shall include the identification of the work, the supplier, the place of installation, the date of replacement and the supporting evidence. We set the requirements according to the process and check the need for qualifications and validation. We do not promise sterileness or suitability for sterilization.

Favourable, cheaper, savings: local in Ljubljana

At the company Svet Črnil in Ljubljana we offer the product for 3 EUR with VAT. We make a favourable choice together with the costs of assembly, checking and possible wrong purchases. It may be cheaper to use one relevant part but only if it meets the requirements of the link. Local demand allows you to transmit dimensions and photo of the connection point before ordering.

Order INOX mount: check data

Send us a threading mark of the device, actual dimensions, photo and information about the tube with an outer diameter of 12 mm. Add the intended medium, pressure, temperature, cleaning method and supporting evidence required. This allows us to check if this combination is 1/8 and 12 mm suitable for your demand.

The exact type of thread G/R/NPT, steel grade, material of all seals, permitted pressure, temperature, media, torque and certificates are not confirmed. We do not replace this data with assumptions. Ask for verification for concrete use before buying!

Is the choice of the cheapest connection really economical if we skip the thread and compatibility checks and leave the risk of congestion to the entire production?

Illustrational display of the series. The appearance of the concrete delivered version may vary; do not specify the dimensions, steel type or certificates from the image.