Pneumatic fast connection 90st male thread 3/8 on tube 12mm INOX

Description

Pneumatic fast connection 90° 3/8 for tube 12 mm INOX

Mounting can fit into the opening and the tube still interferes with the cap. So when choosing, let us look beyond the thread itself! Pneumatic fast connection 90st male thread 3/8 on tube 12mm INOX connects the threaded connection to the pneumatic tube with an external diameter of 12 mm, the axles of the connections being 90 degrees. The direction of the pipe is thus planned at the connection point.

When maintaining and constructing machinery, its applicability is assessed according to dimensions, accessibility and validated operating conditions. The price of the product is EUR 3 with VAT.

INOX mount: confirmed properties

The choice is based on verified data:

• Product: angular high speed pneumatic connection with an eight connections at an angle of 90 degrees.
• Material: stainless steel INOX; exact steel grade not confirmed.
• Thread: male, nominal size 3/8 inches.
• Pipe: a pneumatic tube with an external diameter of 12 mm.
• Price: EUR 3 with VAT.
• Type: goods.

Rotation and operation as rotary couplings are not confirmed. Nor is the standard of thread G/R/NPT, gaskets, pressure, temperature, allowed media, flow, body radius, moment of tightening and certificates confirmed. This information is not determined by the appearance or characteristics of similar products of other producers.

Thread 3/8 and outer diameter 12 mm

The thumb marking of the tube thread is not its direct diameter in millimetres. Codes 3/8 are therefore not converted into millimetres as normal length dimensions and the result is not used to judge the match. Before ordering, we check the standard threading and the opposite connection. The same nominal size alone does not confirm the compatibility of the G, R and NPT performances.

In the case of tubes, a different rule applies: here we choose by external diameter 12 mm. The internal diameter is not given and is not assumed from the mark. Also check material, tolerances and other requirements of the pipe manufacturer and connection. The tube with an internal diameter of 12 mm is therefore not automatically the right choice for this product.

Angular connection and line control by the machine

When the threaded opening looks out of the wall of the machine, we often want to keep the tube along this wall. The angle of 90 degrees allows such a change of direction already in the connection. This can reduce the need for a spatial arc tube directly in front of the casing, but only after checking the actual body dimensions and its final position.

The tube of 12 mm outside diameter should not rub against the edge of the plate, screw or flexible part. Check the way to the next attachment, opening the door and removing the lids. We also leave access to the wall for inspection and cleaning. The shortest route is not always the most useful.

The final orientation is not achieved by unscrewing the already sealed thread or by forcing the pipe to turn. Since the rotational speed is not confirmed, the coupling is not regarded as an adjustable or flexible coupling. The method of installation and achievement of the appropriate position shall correspond to the approved performance.

Release ring and tool access

When deploying, we reserve a space for inserting pipes and access to the release ring. If the ring is pressed between the housing and the adjacent component, later dismantling may be difficult. The access is checked with a tube of 12 mm in the intended position, not only with an empty connection.

Separately, we provide room for the appropriate tool on this intended grip. Neighbouring connections shall not prevent assembly or maintenance. Since the body's dimensions, its radius and moment of tightening are not confirmed, we do not adjust universal mounting distances or forces. We need concrete implementation data.

Tube release and hose bending radius 12 mm

Mounting should not be used as a carrier of the entire tube. Support the hose so that the coupling does not take on unnecessary tow, weight or lateral loads. The attachment should allow the natural running of the hose and access to the service.

The minimum bending radius is taken from the manufacturer's instructions of the selected tube. The outer diameter of 12 mm alone does not indicate how closely we can bend it. We also take into account the conditions of use and the possible difference between stationary and moving wiring. The angular body does not remove the requirements for further turn pipes.

In the case of moving parts, check the entire walk and anticipate proper guidance. The hose shall not pull the coupling, break at exit or use its body as a pivot. We need a dedicated, duly validated solution for repeated rotation.

Angle or level mount 3/8 to 12 mm

The level of connection of the same coupling dimensions is a useful alternative for a different spatial arrangement. We compare geometry and installation requirements, without assuming other properties of the alternative.

Flow and design of the pressure drop

The coupling dimensions 3/8 and 12 mm do not specify the guaranteed flow. In planning we examine the entire route: length and inner diameter of the pipe, number of joints, directional changes, valves and consumer needs. We also take into account the simultaneous operation of consumers.

The pressure drop is estimated with the relevant component data or verified by measurement in the certified operating limits. Since the flow characteristic of this connection is not confirmed, we do not calculate losses from its angle alone. Nor do we promise that the tube of 12 mm diameter will remove the limit elsewhere in the system.

Mounting, damper, threaded knee and rotating coupling

• Angle fast connection: the product under consideration connects the male thread 3/8 to the tube of an external diameter of 12 mm at an angle of 90 degrees. No level connection.
• Diffuse or flow regulator: designed to regulate flow. This product is not a silencer and does not use it to set the speed of the pneumatic drive.
• Two threaded knee: has threaded connections on both sides. Here's a quick hose connection on one side 12 mm.
• Rotating coupling: is intended for specific relative rotation under validated conditions. This activity with this product is not confirmed.

INOX, HACCP and GMP

INOX alone is not evidence of hygiene or compliance. Within the framework of HACCP, i.e. risk analysis and critical control points, the link is considered according to the risks of the specific process. In the case of hygiene planning, therefore, we check the availability, cleaning options, impurity retention sites and status control. Maintenance and exchange are included in the relevant traceability records.

GMP means good manufacturing practice. When designing equipment, it links the suitability of materials, cleaning, controlled procedures, documentation and traceability. In order to contact food or pharmaceutical products, we need appropriate evidence of full concrete assembly, including all gaskets and hoses. Let us also check the actual exposure in the process.

For this connection we do not provide HACCP, GMP or USP certificates, sterility or use with any cleaning and media. The compatibility of cleaners, their concentrations and procedures is checked for all components. Stainless steel does not replace this verification.

General explanations by the European Commission: food hygiene, materials in contact with food and GMP. These sources are not documentation or certificates of this product.

Safe installation and connection check

Before the operation, the system is safely stopped, insulated and relieved and inadvertent movement is prevented. Let's also check for residual energy. The pipes are not released under pressure!

1. Confirm threading standard 3/8, corresponding opposite opening and method of sealing.
2. Check the compatibility of the pipes with the outer diameter of 12 mm and the certified operating limits of the whole assembly.
3. After proper instructions, prepare the hose, mount the coupling and check the correct insertion and retention of the pipe.
4. We arrange relief, allowed bending and access for the ring and tool.
5. After the prescribed procedure, we check the tightness and operation and record the operation when required by the maintenance system.

Affordable and local: Ljubljana

For 3 EUR with VAT we offer a clearly defined corner connection INOX. If we want to do the job cheaper, we also look for savings in the right choice and accessible wiring. A favorable order makes sense when the product fits the installation site.

The company Svet Črnil in Ljubljana invites you to the inquiry! Send thread label, tube data 12 mm, photo of space and required conditions of use. This allows us to check what information we need before deciding to mount 90° with male thread 3/8.

The picture of the series is illustrious; the appearance of the concrete performance may deviate.

Is it really a saving if we accept a compressed tube and a joint that we cannot access when maintaining for 3 EUR?